Replace your leaking transmission lines with our heavy duty, high flow, flexible transmission lines. Our kit is the most complete replacement transmission line kit available for your LB7 or LLY...
Replace your leaking transmission lines with our heavy duty, high flow, flexible transmission lines. Our kit is the most complete replacement transmission line kit available for your LBZ or LMM...
Replace your plastic OEM fuel cap with this stylish billet black anodized fuel cap. It comes with a double o-ring seal to ensure a tight fit and keep contaminates out...
Increased Coolant Flow, Decreased Coolant Temperatures, The rear cylinders on the 5.9/6.7L Cummins suffer from a lack of coolant flow, and therefore, experience the highest coolant temperatures. This can cause...
Turn over your Cummins with ease with this Cummins Crankshaft Barring Tool. Features: Accepts 1/2 inch drive ratchet Designed to be used with factory crank bolts and roll pins No...
The Cummins Turbo Drain Tube Adapter is made from high quality 6061 aluminum and anodized black for a superior appearance. It fits into the block like the factory drain tube,...
Put the finishing touches on your truck with this high quality Cummins Turbo Drain Tube Kit. The tube is braided stainless steel for durability on the exterior, and corrugate teflon...
Whether you're putting on an aftermarket turbo or deleting the EGR system on your LML, this coolant return plug will help you put the finishing touches on the job. The...
The Fleece Performance Duramax Turbo Thermostat Delete Plug is designed to eliminate the stock coolant feed line when installing a non-water cooled turbocharger on your Duramax. It provides clearance for...
TufShafts are a direct replacement upgrade shafts for any 2001-2010 GM 2500-3500 with a 9.25 inch AAM front axle. They are designed to eliminate the stock passenger side split axle...
Replace your plastic OEM fuel cap with this stylish billet green anodized fuel cap. It comes with a double o-ring seal to ensure a tight fit and keep contaminates out...
The Fleece Performance Intake Air Heater Delete is a simple way to remove the air intake heater on your 2001-2004 GM 6.6L Duramax. Complete with a pre-drilled and tapped ports...
Increase your LB7's potential with this simple but effective upgrade. Back-to-back dyno pulls showed an increase of 15hp with this Fleece Performance high flow LB7 intake horn- that's about the...
Want to get rid of that big ugly resonator under the hood of your LML? This billet aluminum plate, anodized in black with Fleece engraved across the top will take...
Fleece Performance Tie Rod Sleeves are a must for any 99-10 GM 2500-3500HD pickup that utilizes four-wheel drive. These support sleeves keep the weak factory tie rods from bending under...
Fleece Performance LML Tie Rod Sleeves are a must for any 2011 and up GM 2500-3500HD pickup that utilizes four-wheel drive. These support sleeves keep the weak factory tie rods...
Mitre Cut Fleece Performance hood stack covers are made from heavy duty vinyl and come complete with a properly sized band clamp to ensure a tight fit.
The Donaldson P555095 Fuel Filter is a direct replacement filter for use with the Fleece Performance Engine Mounted Filter Assembly for 6.7L Ford Powerstroke, part number FPE-FMC-UHFA-1123. Fits the following...
Fuel heater kit specifically for use in Fleece Performance heated fuel filter kits installed on 2011-2016 Ford 6.7L Powerstroke.������This kit includes the fuel heater and chassis harness to provide switched...
Replace your leaking or corroded heater tubes with our upgraded stainless steel tubes and high temperature silicone hose kit from Fleece Performance. This kit contains everything you need to replace...
The exhaust back pressure relocation Kit for 2007.5-2012 RAM w/ 6.7 Cummins will allow you to relocate the EBP sensor from the factory location on thermostat housing elbow to a...
